
How to Clean Composite Decking Properly Without Wrecking the Boards
Mark Cave breaks down why composite decking requires a completely different approach to timber, covering board identification, pressure limits, and chemical safety to avoid permanent damage.
Chapter 1
Low Maintenance Is Not No Maintenance
Mark Cave
Composite decking is low maintenance. It is not no maintenance. That one misunderstanding causes more damaged decks than almost anything else I hear about, and it usually starts with a customer being told the boards will never need touching.
Mark Cave
I'm Mark Cave from SoftWash UK, and today we're looking at how to clean composite decking properly, and why the habits that work on timber can wreck it.
Mark Cave
If you listened to our earlier episode, The Full Decking Protocol, you'll remember the sequence for timber. Clean it, brighten it with a wood restorer, then feed it with a penetrating oil. That works because timber is porous. It drinks the oil. Composite boards cannot absorb oils. So if you carry those timber habits across to composite, you're heading for disaster. Oil and stain sit on top of the surface, attract dirt, and turn into a sticky, slippery mess. Composite needs a completely different surface and chemical approach.
Mark Cave
First, what are you actually standing on? There are three broad types, and identifying the board decides everything that follows.
Mark Cave
One is first generation uncapped composite. That's a mix of wood fibre and recycled plastic. It's softer and more porous, so it holds mildew deeper, and if you scrub or blast it aggressively the surface fuzzes up.
Mark Cave
Two is modern capped composite, such as Trex or NewTechWood. These have a protective polymer cap that resists rot and moisture. But that cap is thin. A wand can score it permanently, and you get what people call tiger striping.
Mark Cave
Three is moulded mineral resin board, such as Millboard. That's a polyurethane and mineral core with an elastic outer surface called Lastane. Different again, so check the manufacturer's guidance before you start.
Mark Cave
If you can't tell which you have, ask the installer or look for the brand. Don't guess. Uncapped boards in particular are softer and more porous, and high pressure can open the surface up.
Mark Cave
Now the mechanical limits, because this is where contractors get caught out. Composite looks tough, so people reach for the pressure washer. The guidance from the sources I've looked at is a maximum of 1,500 PSI, a wide fan tip, around 40 degrees, with the nozzle held at least 20 to 30 centimetres off the surface, and always moving along the grain.
Mark Cave
Pinpoint tips, zero degree nozzles and turbo nozzles are out. So are wire brushes and metal scrapers. Wand marks on capped composite are permanent. One US decking specialist makes the same point, that the cap is a thin outer layer and a narrow tip will strip it in stripes. And a concentrated jet can force water into the board's core. You can't fix that with a second pass. You own it.
Mark Cave
That's why this job is softwashing territory. Let the chemistry and dwell time do the work, not pressure.
Chapter 2
Cleaning It Without Wrecking It
Mark Cave
So what are you cleaning off? In the UK, mostly damp and shade. Algae, mildew and pollen settle in the grain and the grooves between boards and build into a thin biofilm. It dulls the deck and makes it slippery. The boards are not the problem. It's what grows on top of them.
Mark Cave
Here's the workflow I'd follow.
Mark Cave
Start with a survey. Identify the board type and look at the fixings. Hidden fixing clips and the sub frame matter, because aggressive chemistry can get down into the gaps.
Mark Cave
Then clear the deck. Furniture, planters, rugs, loose debris. Clear out the drainage gaps between boards, because if water can't flow through, it sits and feeds the growth. Rugs and planters left in place also cause shadow marks through uneven weathering.
Mark Cave
Next, pre wet the boards. Then apply mild, composite safe chemistry.
Mark Cave
On bleach, be honest with yourself. Heavy sodium hypochlorite can discolour boards and degrade the cap over time, and Trex specifically warns against bleach on their boards. Bleach can also attack hidden metal fixings. A low concentration mix with a bleach compatible surfactant like Clever Wash can be used for a rapid kill of organic growth, but only if you keep it controlled. Test a small area first. Never let it dry on the board. Rinse thoroughly. And check the manufacturer's position first, because on some brands you'll be going against their advice.
Mark Cave
My preference on a lot of these decks is a mild residual biocide, a DDAC based product like Soft Wash Pro 50. It doesn't bleach, it kills the spores, and it keeps working afterwards. The trade off is that results come gradually, so you have to tell the customer that upfront.
Mark Cave
Then agitate gently. A soft to medium bristle deck brush, working strictly with the grain. Never across it, because you'll leave scratches, especially on lighter boards. For stubborn patches, let the product dwell first and let it loosen the growth, rather than scrubbing harder.
Mark Cave
Finish with a thorough, low pressure fan rinse, again with the grain. Don't skip this. Dried detergent can leave a white haze on dark boards. Check that water is flowing freely through the gaps.
Mark Cave
Not every stain is biological, and this catches people out. Brown marks under trees are usually leaf tannins. Orange marks under metal furniture or planters are rust. Bleach and detergents won't shift either. They need a mild acid, such as oxalic acid, and you spot test it first. If it's rust, find the source or it will come back.
Mark Cave
And be clear about limits. Cleaning removes dirt and growth. It won't remove scratches, and fading on old uncapped boards can be permanent. Say so in the quote, and take before photos.
Mark Cave
A routine of a proper clean in spring and autumn suits most decks, more often if it's shaded. And never use deck stain, oil or traditional sealer on composite.
Mark Cave
Podcasts like this are a great start, but if you're serious about offering softwashing professionally, the SoftWash UK CPD Certified Softwash Training Course goes much deeper into surface identification, chemical selection, safety and real world application. It's online, so you learn at your own pace, and completing it lets you become an Approved Softwash Applicator, with a directory listing and a place in the National Association of Softwash community. Have a look at softwashing.uk.
Mark Cave
Before your next composite job, ask yourself one question. Do I actually know what board this is? If the answer's no, stop there. Take care, and I'll speak to you again soon.