The Mark Cave Softwashing Podcast
All Episodes
Mastering the Site Survey: What to Check Before Quoting

Mastering the Site Survey: What to Check Before Quoting

0:00|0:00

Mark Cave shares a step-by-step pre-job survey checklist to help exterior cleaners diagnose stains, identify surface damage, protect vulnerable surroundings, and avoid costly mistakes before quoting.


Chapter 1

The Survey Is The Job

Mark Cave

Most of the money contractors lose on a job is gone before a single drop of chemical leaves the van. It goes at the survey. A rushed look at a wall, a quick measure, a price on the doorstep, and you've already made the mistakes that cost you later. I'm Mark Cave from SoftWash UK, and today I want to build a survey checklist with you, step by step.

Mark Cave

If you listened to the recent episodes on porosity and wand marks on render, this follows on naturally. Because the contractor who gets wand marks is usually the one who treated the wall as a simple wash job. A survey is not just measuring for a price. It's a risk and condition audit, and it protects you.

Mark Cave

Start with the surface. What exactly is in front of you? Modern render like monocouche, silicone or acrylic, the K Rend, Parex and Weber type systems? Or traditional sand and cement? Or painted masonry? On paving, is it natural sandstone or limestone, or reconstituted stone? On a roof, clay or concrete tile? Getting that wrong changes your chemistry, your test patch and your customer's expectations.

Mark Cave

Then look at the condition. Hairline cracks. Blown render. Tap it, and listen for hollow spots. Spalled brick, crumbling or lime mortar joints, loose flashing. If water can get behind a surface, a rinse will find it.

Mark Cave

And look for what somebody else did before you. Wand marks, pressure gouges, chalking paint, peeling coatings, efflorescence. I've seen contractors blamed for damage that was there for years, simply because nobody recorded it. If you document it at the survey, it's a fact. If you find it halfway through the job, it's an argument.

Mark Cave

Next, diagnose the stain before you pick the chemical. Is it biological? Green algae, red Trentepohlia, black spot lichen, fungal biofilm. Or is it inorganic? Iron oxide beneath a fixing, lead run off under flashing, carbon pollution, efflorescence salts. The location is your clue. Streaks below a metal fixing are not algae.

Mark Cave

For biological growth, you're generally looking at an oxidiser like sodium hypochlorite, or a residual quaternary biocide such as DDAC. Soft Wash Pro 50, for example, is a 50 percent DDAC concentrate, and its guide rates are a 1 percent working solution for maintenance cleans and 2 percent for heavier first time cleans. And with those, results often keep improving as weathering happens. That's something you tell the customer up front.

Mark Cave

For rust and lead, bleach isn't the answer. You need an acid approach, like oxalic acid, with a test patch first. And never, ever mix acids with sodium hypochlorite.

Mark Cave

Then think about how it will cling. A surfactant helps wetting and dwell time on vertical, textured surfaces. Clever Wash has a guide rate of 200 to 1, which is 5 millilitres per litre of your recipe. On delicate vertical render, a clinging gel like Gel X Pro is designed for brush, roller or low pressure application, with a typical dwell of 1 to 24 hours. But it targets organic staining. It won't touch rust or mineral marks. Which is why you diagnose first.

Chapter 2

Environment, Access And Evidence

Mark Cave

Now the environmental audit. Walk the site and find the drains. Surface water gullies often run straight to a river or soakaway, and softwash solutions must never enter them. Know which drains are which before you mix anything.

Mark Cave

Look at what's vulnerable. Fishponds and aquatic life, ornamental planting, lawns, pet areas, parked cars, the neighbour's boundary. Then the trap materials. Untreated aluminium frames, zinc valleys, lead flashings, copper, coated glass. Those are the ones that turn a good clean into a costly phone call.

Mark Cave

Then the practical realities. Check the water supply. Litres per minute, tap pressure, how far the hose has to run. Check access. Fragile roofs, a conservatory underneath your work area, overhead power lines, and whether it's a ladder job or needs a tower or MEWP. And check the property itself. Unsealed vents, open trickle vents, warped frames, electrical sockets, security cameras.

Mark Cave

Finally, evidence. Take wide establishing shots, then close ups of cracks, failed joints and metallic stains. Put your findings into the quote and your job pack and RAMS. And get the customer's written sign off, including the point about instant versus gradual results, before you mix a drop. That one piece of paper has saved a lot of people a lot of grief.

Mark Cave

Podcasts like this are a great start, but professional softwashing is built on process, surface knowledge and survey discipline, not just buying chemicals. If you want to go deeper, the CPD Certified Softwash Training Course at softwashing.uk lets you learn online at your own pace. It can lead to becoming an Approved Softwash Applicator, a directory listing, and joining the National Association of Softwash community.

Mark Cave

Here's your challenge. On your next job, don't quote until you've worked through every point we covered today. See how many things you'd normally have missed. Thanks for listening, and I'll catch you in the next one.