The Mark Cave Softwashing Podcast
All Episodes
The Full Decking Protocol: Clean, Brighten, and Oil Without Ruining Timber

The Full Decking Protocol: Clean, Brighten, and Oil Without Ruining Timber

0:00|0:00

Mark Cave breaks down the full professional wood protocol for decking: clean, brighten, and oil. Learn why pre-wetting protects timber fibres, how to safely mix and dwell low-strength hypochlorite, and why brightening and drying times are essential before sealing.


Chapter 1

The Thirsty Wood Trap

Mark Cave

Dry timber is a sponge. That's the whole problem with decking in one sentence. Spray sodium hypochlorite onto a bone dry board on a hot July afternoon, and it doesn't sit on the surface. The board drinks it. And once it's in there, you can't get it back out.

Mark Cave

I'm Mark Cave from SoftWash UK, and this one connects back to the episode on porosity and water absorption, where we talked about how pre-soaking protects timber but can ruin a treatment on stone. Today it's the full wood protocol: clean, brighten, and oil.

Mark Cave

Online there are two camps. The pressure washing cowboys with a lance chewing the boards up, and the purists who say bleach should never touch wood. I think both are arguing about the wrong thing. The question isn't whether you can use hypochlorite on wood. It's what state the wood is in when the chemical lands.

Mark Cave

Wood is cellulose fibres held together by a natural glue called lignin. Sodium hypochlorite is an oxidiser, so once it's pulled deep into the capillaries, it keeps attacking that lignin. The fibres lose their glue. You get that furred, grey, driftwood look. Brittle, splintering, weaker than it was.

Mark Cave

You might think, well, I'll just rinse harder. It doesn't work. Rinsing the surface doesn't pull chemical out of the middle of a board. The damage is done by the draw, not by the dwell.

Mark Cave

So the rule is, wet it first. Properly. Not a sprinkle. Drench it with clean water and let it sit so the fibres plump up. A full sponge can't drink any more. Then when your mix goes on, it stays in the outer few microns, and that's exactly where the algae and fungal growth live anyway. You're not treating the board. You're treating the skin.

Mark Cave

Here's a scenario I'd happily use in training. A contractor turns up to an expensive cedar deck, hot afternoon, sun baked. He's got a patio mix in the sprayer, about 4%, never measured, just glugged it in. No pre wet. Within the hour that lovely deck is bleached, splintering driftwood. And then comes the bit nobody budgets for. The customer wants the boards replaced, and it eats the profit from twenty other jobs. All from skipping a hose and a measuring jug.

Mark Cave

So what should the recipe be? Green algae on decking is soft. You don't need roof or patio strength. You want about a 1% working mix, and 2% at the very most for heavy biofilm. From a 15% stock drum, 1% is a one to fourteen ratio. One part sodium hypochlorite, fourteen parts water. That's roughly 6.6 litres of hypochlorite in every 100 litres of mix. Work it out from the strength on the drum, not the strength you hope is on the drum.

Mark Cave

Add a bleach compatible surfactant. With Clever Wash the guide rate is 200 to 1, which is 5ml per litre of mix. It breaks the surface tension so a weak mix clings and wets the slime without you going stronger. Dwell ten to fifteen minutes, strictly timed. Not 'I'll go and have a brew.' Never let it dry on the boards. Then rinse thoroughly, low pressure, high volume. A high pressure lance raises the grain and furs the wood permanently.

Mark Cave

One exception. Oily, dense hardwoods like teak or iroko. Generally, keep hypochlorite away, because you risk stripping the natural oils. A gentle wash followed by a non oxidising DDAC biocide, like Soft Wash Pro 50, suits those far better.

Chapter 2

Brighten, Wait, Then Oil

Mark Cave

Even a perfect clean can leave timber looking pale, a bit yellow, chemically tired. Customers notice that, and they think you've ruined it. That's where brightening comes in.

Mark Cave

Wood X Pro is an oxalic acid brightener. Order matters. Hypochlorite on, then rinsed off completely, and only then the acid. Those two must never meet in the same bucket, because mixing them releases dangerous toxic gas. Apply it at about 1 litre per 4 to 5 square metres, by spray or brush, leave it until you get the effect, then rinse fully. It neutralises the alkaline salt residues, resets the surface pH, and that warm honey grain comes back in front of your eyes. That's the moment customers remember.

Mark Cave

Then the mistake right at the finish line. The deck looks great at two in the afternoon, the customer says, can you oil it today? And he does. Wet boards, oil on top, moisture sealed in. Peeling, black rot underneath, and a phone call in three months.

Mark Cave

Let the decking dry naturally. That could take 24 to 48 hours depending on the UK weather. Dry timber lets the oil go deep, gives an even finish, and protects against moisture and UV. The wait isn't optional. It goes in the quote.

Mark Cave

So, the takeaways. Wet it first. Go weak, around 1%. Add the surfactant. Time the dwell. Rinse gently. Brighten after a full rinse. Wait before oiling. That's the whole deck, really.

Mark Cave

Podcasts like this are a great start, but guesswork kills your margin, and one ruined cedar deck can wipe out a month of good work. The SoftWash UK CPD Certified Softwash Training Course goes much deeper into chemical selection, surfaces, safety and pricing, and you learn at your own pace online. Finish it and you can become an Approved Softwash Applicator, get listed in the directory, and join the National Association of Softwash community. Have a look at softwashing.uk. Take care, and I'll speak to you again soon.